Subversion Repositories svnkaklik

Rev

Rev 1159 | Rev 1166 | Go to most recent revision | Show entire file | Ignore whitespace | Details | Blame | Last modification | View Log

Rev 1159 Rev 1162
Line 1... Line 1...
1 
\chap Trial version of the digitizer
 1 
\chap Trial version of the digitizer
2 
 
 2 
 
3 
The whole design of the radioastronomic receiver digitization unit is meant to be used in a wide range of applications and tasks related to digitization of a signal. A good illustrating problem for its use is the signal digitization from multiple antenna arrays. Design and implementation of the system is presented in this chapter.
 3 
The whole design of the radioastronomic receiver digitization unit is meant to be used in a wide range of applications and tasks related to digitization of a signal. A good illustrating problem for its use is the signal digitization from multiple antenna arrays. Design and implementation of the system is presented in this chapter.
4 
 
 4 
 
5 
\midinsert
 - 
 
6 
\clabel[expected-block-schematic]{Expected system block schematic}
 - 
 
7 
\picw=\pdfpagewidth \setbox0=\hbox{\inspic ./img/Coherent_UHF_SDR_receiver.png }
 - 
 
8 
\par\nobreak \vskip\wd0 \vskip-\ht0
 - 
 
9 
\centerline {\kern\ht0 \pdfsave\pdfrotate{90}\rlap{\box0}\pdfrestore}
 - 
 
10 
\caption/f Expected realization of signal digitalisation unit.
 - 
 
11 
\endinsert
 - 
 
12 
 
 5 
 
13 
\sec Required parameters
 6 
\sec Required parameters
14 
 
 7 
 
15 
We require the following technical parameters in order to overcome the existing digitization units solutions. Primarily, we need a wide a dynamical range and a high third-order intercept point (IP3\glos{IP3}{Third-order intercept point}). The receiver must accept signals with the wide dynamics because a typical radioastronomical signal is a weak signal covered by a strong man-made noise or other undesired noises as lighting, Sun emissions, etc.
 8 
We require the following technical parameters in order to overcome the existing digitization units solutions. Primarily, we need a wide a dynamical range and a high third-order intercept point (IP3\glos{IP3}{Third-order intercept point}). The receiver must accept signals with the wide dynamics because a typical radioastronomical signal is a weak signal covered by a strong man-made noise or other undesired noises as lighting, Sun emissions, etc.
16 
 
 9 
 
Line 56... Line 49...
56 
 
 49 
 
57 
This design ensures that all system devices have access to the defined phase and the known frequency.
 50 
This design ensures that all system devices have access to the defined phase and the known frequency.
58 
 
 51 
 
59 
\sec System description
 52 
\sec System description
60 
 
 53 
 
61 
This section deals with the description of the trial version based on Xilinx ML605 development board, see Figure~\ref[ML605-development-board], available at the workplace. This FPGA parameters are more than sufficient of what we need for the fast data acquisition system being developed.
 54 
This section deals with the description of the trial version based on Xilinx ML605 development board, see Figure~\ref[ML605-development-board], available at the workplace. This FPGA parameters are more than sufficient of what we need for the fast data acquisition system being developed. Expected system configuration is shown in Figure~\ref[expected-block-schematic]. The system consist antennas equipped by
- 
 
 55 
 
- 
 
 56 
%% dopsat celkovy popis systemu.
- 
 
 57 
 
- 
 
 58 
\midinsert
- 
 
 59 
\clabel[expected-block-schematic]{Expected system block schematic}
- 
 
 60 
\picw=\pdfpagewidth \setbox0=\hbox{\inspic ./img/Coherent_UHF_SDR_receiver.png }
- 
 
 61 
\par\nobreak \vskip\wd0 \vskip-\ht0
- 
 
 62 
\centerline {\kern\ht0 \pdfsave\pdfrotate{90}\rlap{\box0}\pdfrestore}
- 
 
 63 
\caption/f Expected realization of signal digitalisation unit.
- 
 
 64 
\endinsert
- 
 
 65 
 
62 
 
 66 
 
63 
\secc Frequency synthesis
 67 
\secc Frequency synthesis
64 
 
 68 
 
65 
We have used a centralized topology as a basis for frequency synthesis. One precise high-frequency and low-jitter digital oscillator (GPSDO\glos{GPSDO}{GPS disciplined oscillator}) has been used \cite[MLAB-GPSDO]. The other working frequencies have been derived from it by the division of its signal. This central oscillator has a software defined GPS\glos{GPS}{Global Positioning System}  disciplined control loop for frequency stabilization.\fnote{SDGPSDO design has been developed in parallel to this diploma project as a related project, but it is not explicitly required by the thesis itself and thus it is described in a separate document.}
 69 
We have used a centralized topology as a basis for frequency synthesis. One precise high-frequency and low-jitter digital oscillator (GPSDO\glos{GPSDO}{GPS disciplined oscillator}) has been used \cite[MLAB-GPSDO]. The other working frequencies have been derived from it by the division of its signal. This central oscillator has a software defined GPS\glos{GPS}{Global Positioning System}  disciplined control loop for frequency stabilization.\fnote{SDGPSDO design has been developed in parallel to this diploma project as a related project, but it is not explicitly required by the thesis itself and thus it is described in a separate document.}
66 
We have used new methods of software frequency monitoring and compensation in order to meet modern requirements on the radioastronomy equipment, which needs the precise frequency and phase stability over a wide baseline scales for effective radioastronomy imaging.
 70 
We have used new methods of software frequency monitoring and compensation in order to meet modern requirements on the radioastronomy equipment, which needs the precise frequency and phase stability over a wide baseline scales for effective radioastronomy imaging.